How to Replace a Mazda Key
Mazda is a brand known for its innovative and intuitive technology. Some of these systems improve safety or performance, while others make driving your Mazda around East Stroudsburg, Easton, and Brodheadsville simpler.
The key fob, for instance, is a good example of this. It lets you lock, unlock, and start your Mazda with a button push. However, its battery needs to be replaced every now and then.
Lost Keys
Keys that are stolen or lost could be a major issue. It is relatively simple to replace a Mazda Key for older models using regular keys made of metal. However, newer cars need special programmable computers chips which can only be manufactured by a dealer or locksmith.
You must begin by getting the VIN number for your vehicle. It's usually located on the driver's side of the dashboard or on your insurance certificate, or in the vehicle's papers. Write down this information to give to the locksmith or dealership.
You'll also need a working spare key. Place the key in the slot and turn the ignition ON. After about five seconds, you can remove the key and turn off the ignition off. Repeat this procedure with the second key. Once both keys have been installed, the new computer chip will become paired with your car.
If you have lost the keys to your car and do not have an extra set, you'll need to tow the vehicle to an auto dealer. Then, you'll need to prove ownership and pay for an alternative key. It could take a few days for the dealer to order and match a replacement key with your vehicle. You will save time and money by having a locksmith replace your key, instead of going to the dealer.
Ignition Cylinder Replacement
The ignition cylinder of your Mazda is the main component that makes it possible to start your car using the key. If your Mazda isn't turning over or you are unable to put the key into the switch, you may require replacing the ignition cylinder.
Ignition cylinders are more likely to fail than the keys which last longer. There isn't any requirement to adhere to any specific maintenance plan, however, keeping your keys clean will make it last longer.
To replace the ignition coil, take out any covers or trims that are in the way. Depending on the model, you might have to remove the cover of the steering wheel. You may also need to remove the accessory switch and wiper. Use an socket wrench or screwdriver to depress the release tab of the cylinder. This will release the cylinder from its switch and allow it to slide away.
Install the new cylinder by connecting the wires to it, tightening the two screws at the top and then replacing the switch. Reconnect the battery and ensure whether the new cylinder is able to move keys in and out. Do this three to five times, and then reconnect the battery and attempt to start the vehicle to ensure everything is working properly.
Remote Control Replacement
If your Mazda key remote stops working, you'll need an expert to get it back to working. While this isn't nearly as common as an ignition cylinder issue but it does happen and can leave you in some situations. A locksmith can replace the car remote and take care of all the programming associated with it.
You'll need tell a locksmith the year and model of your Mazda car to have them complete this. This will allow them to gather the appropriate equipment and know what they will need to do any additional key programming for your particular model of Mazda.
It could be that the battery in your key fob is not fully charged. In this situation, the best thing to try is to reset your receiver. This is often able to restore functionality. If this doesn't work, you'll have to replace the battery. To accomplish this, you'll need to take the key off of the metal and then make use of a tape-wrapped flathead screwdriver to pry open the case on one side, then on the other. After that then, you can insert a new battery into the key fob. Make sure it's a compatible battery, and then close the case. The RF unit inside your Mazda will have to be programmed to recognize the new key.
Transponder Chip Replacement
If you own a Mazda key fob or smart key, chances are that your car has a transponder inside it. This tiny piece is basically a mini motherboard that, when inserted into the ignition, sends a signal to your car's immobilizer to let it know that this key is the correct one for your vehicle.
These keys are great for security as they prevent others from getting your car started. They do this by ensuring that only you have the ability to start it. Be very cautious not to lose or take your key.
A professional locksmith can replace chip for transponder replacement. To do this, you'll need to remove the cover from your key fob. Usually, it's a thin piece of plastic that can be removed with either pliers or a screwdriver. Then, you will need to remove the chip. It should appear as a tiny black square or a transparent tube. After that, just place the chip on a piece tape and attach it near to the ignition lock.
A locksmith who is experienced can complete this task in a flash, and will help you get back on the road swiftly. If mazda key fob battery having issues with your Mazda key, contact a trusted mobile locksmith right now.
